If you are wondering what Fire Alarm Call Point is, you’ve come to the right place. This article will discuss the different types, placement, and testing requirements of manual call points. There are many benefits to manual call points, so you’ll want to use them whenever you’re in a fire. Here are some things to know before installing one. Also, read on to find out how to reset them.
Manual call point
A manual fire alarm call point is like an addressable smoke or fire alarm system. It may be made of aluminum or GRP and is usually sealed with an IP66 or IP67 rating. Some models are design for outdoor or dusty locations, and the addressable variety is specializ to prevent heat from starting an ignition. Manual fire alarm call points are useful to help protect people in case of an emergency. They may also be configured to unlock doors or turn off air-conditioning systems.
A manual fire alarm call point will trigger the fire alarm system when a fire is detected. It should be installed close to the fire exit so that everyone can find it in time to escape. The location of the call point does not need to be surrounded by signage or a door to make it easy to find. Unlike an automated fire alarm, it is not necessary to have signage for the manual call point. Most manual call points are installed on walls.
Manual pull-station
A manual pull-station for fire alarm call points is a device that triggers the fire alarm system by pulling a cord. This type of system is primarily use in the US and Canada. However, the European standard for fire alarm call points is now widely used around the world. In addition to providing fire safety and security, a manual pull-station can be used to monitor a building’s security and emergency response systems.
A manual pull-station can be single-action or dual-action, addressable, or non-addressable. To activate the device, the user must push a lever on a cover and pull the trigger. The latter prevents accidental activation of the fire alarm system due to accidental push-pull actions. Nevertheless, the manual pull-station is not without its own drawbacks. Here are some examples of manual pull-stations:
Fire Alarm Call Point Placement
The correct place for manual fire alarm call points is near exit doors and other exit routes. The call point should be within 45m of the nearest person and should project 15mm from the wall. However, a lower mounting height can be negotiated and recorded on a fire alarm certificate. Manual call points should be in an accessible location that is easily Find by people in wheelchairs. The fire safety code recommends placing manual call points at least one meter from an exit route.
The number of fire alarm call points should be at least five per room. Fire alarm call points should not be more than eight per zone. A minimum of two fault isolators per 20-30 manual call points and detectors is required. A monitoring base station unit should be installed on the first floor or at a level above the first floor. It should monitor radio signal strength, battery life, and triggering units. Radio receivers should be Category 1 standard.
Testing of Fire Alarm Call Point
When testing fire alarm call points, end users often make some common mistakes. One mistake is activating a fire alarm from the front of the control panel, not from a manual call point. This is the incorrect way to activate a fire alarm, as it does not activate the output equipment, such as text or zone information. To avoid this error, make sure that the alarm activation switch is in the manual mode, and insert the test key into the manual call point.
After each test, the Responsible Person should record dates, times, and locations of system tests and servicing. He or she must also record any disconnection or alterations to the system. The Responsible Person can test the fire alarm call point once a week, by pressing a button on a small trigger. Older systems may require unscrewing the front panel to access the call point. Regardless, of the type of fire alarm call point, a weekly test is the most effective way to determine the health and safety status of a system.
Covers
There are two types of fire alarm call point covers available. The surface mounted ones are ideal for protecting electrical switch points. They are design to fit over a variety of different switches and do not restrict the legitimate use of call points. These fire alarm call point covers are made from tough polycarbonate and have spring-loaded hinge mechanisms. They are available in both surface mounted and flush-mounted styles. You can also use manual call point stoppers.
Manual call points need protective covers. These covers prevent accidental activation by impact. By forcing users to lift the cover before activating the alarm, the accidental triggering of the system is significantly reduced. Added to this, they make people think twice before activating the alarm. If you’re considering putting fire alarm call point covers on your premises, these covers will help you meet British Standards. Just make sure to check the label carefully and follow the instructions.
Add Comment